Took the first step towards building my shop

**Frank S** · Jan 1, 2023, 09:00 PM

I now have doors all the way round the shop so I can close it up to the worst of the wind.
the latest door is 17 ft by 17 ft to complete the 48 ft wide opening

Took the first step towards building my shop-img_20230101_135246d.jpg

Took the first step towards building my shop-img_20221221_181640ddd.jpg

**Toolmaker51** · Jan 4, 2023, 11:55 AM

Link opened with Day 1, a bare frame with a scant roof, 29 Nov 2018. [I]Everyone who knows me are probably familiar with my work shop or lack there of conditions.[/]

Who can say this isn't extraordinary accomplishment; occurring along with large quantity of tools, some connected to the construction, some not, and outside work taken on!

**metric_taper** · Jan 4, 2023, 08:01 PM

I enjoyed his build. Frank is so lucky to live in a FREE country, that does not have building authorities inhibiting his quality constructions as his methods are not in the International Building Code manual.

**Frank S** · Jan 4, 2023, 09:30 PM

Originally Posted by metric_taper

I enjoyed his build. Frank is so lucky to live in a FREE country, that does not have building authorities inhibiting his quality constructions as his methods are not in the International Building Code manual.

One thing with the west doors being so huge and constructed of relatively lightweight materials as compared to most door of this size they are meant to have flex in high winds. Just like a sail sheet on a boat stretches in the wind but will remain effective. The other day my neighbor brought something over for me to machine for him he drove his truck inside and since the wind was blowing pretty good I closed the doors and secured them. Not long afterwards while he and I were standing in the shop talking there were a few huge wind gusts. Billy asked is my truck safe inside here with that door flexing like it does.
Sure I said part of the reason of the Latice design in the pipe work is to allow the door to bow in the wind but not fail We later learned that there had been a few 50+ MPH gusts directly out of the west Had the door not been secured it may have been some of a problem but a ridged door of that size would have been a problem if left unsecured as well. I have opened and closed the door in 30 MPH winds without problems

**mwmkravchenko** · Jan 5, 2023, 07:00 AM

Looking great Frank. You bring in full rigs I am guessing with that height. I know you have the length to do that. Although a tractor and trailer might not fit. I can't remember the other shop dimension.

You can get away with a lot different construction versus up here. You have to account for show load here to. Makes roofs a little more beefy. And frost. You have to sink supports deeper, about 5 feet for southern Ontario. Oh and heat! It gets cold here in the winter, although up till now we have had relatively warm weather above 32 up until today. High in the mid 40's.

You have a great shop. Basically a pole barn. A well made pole barn at that.

**Frank S** · Jan 5, 2023, 02:46 PM

Originally Posted by mwmkravchenko

Looking great Frank. You bring in full rigs I am guessing with that height. I know you have the length to do that. Although a tractor and trailer might not fit. I can't remember the other shop dimension.

You can get away with a lot different construction versus up here. You have to account for show load here to. Makes roofs a little more beefy. And frost. You have to sink supports deeper, about 5 feet for southern Ontario. Oh and heat! It gets cold here in the winter, although up till now we have had relatively warm weather above 32 up until today. High in the mid 40's.

You have a great shop. Basically a pole barn. A well made pole barn at that.

Yep it is a pole barn alright, the steel poles are buried in the ground to about 6 to 8 feet average all of them have at least 1 truck rim welded to their bottoms

**bimmer1980** · Today, 10:26 AM

Just got done reading the whole thread. Lots of work here! I admire the level or repurposing of materials and the efforts. Curious if you have a current update on the shop?

**Frank S** · Today, 12:53 PM

Originally Posted by bimmer1980

Just got done reading the whole thread. Lots of work here! I admire the level or repurposing of materials and the efforts. Curious if you have a current update on the shop?

Not really, I've just been using it Sometimes I get to thinking I need to add another 60 by 100 feet to the back of it and a 40 by 50 to the south of the big front doors but right now 3 things keep changing my mind Time materials and taxes well 4 when you get right down to it. Kind of hard to justify spending the money for the materials since my useable repurposed stock has dwindled to the point, I wouldn't have enough to add on a 20x30 addition