This one for skid loader
https://www.ebay.com/itm/111000876029
I have had good success with hole saws cutting through plate steel, tubing, etc, but it's critical to turn them slow.... I use my vertical mill with it in low gear and turned down about as slow as it will go. Lots of cutting oil, and it works fine. I'm routinely cutting 1.5" holes, and 2" holes through steel plate and tubing.
Depending on frequency, they last for many cuts, but not super long. I have had better success with name brand hole saws like Lennox, but also decent success with the Lowe's brand Kobalt.
I'd like to try the annular cutters at some point.
I mostly try to use my hole saws for wood aluminum or steel less than 1/4" thick. My frill press is hard to change speeds so I leave it on the lowest but that is still 325 RPM. too fast for the 3 1/2 to 5 " saws I have for anything other than softer materials.I have a 3/4" hand drill with 2 speeds 155 RPM low 375 high there abouts It works good but hard to control that leaves the mill it is 3 Hp but also belt drive so again PITA to change speeds. My annulars only go up to 1" Some day I would like to increase my selection of them up to 2" 1/16" or 1/32" I'd like to have 2" depth cutters but I have to buy things like this 1 at a time as pricey as they are.
Never try to tell me it can't be done
When I have to paint I use KBS products
Good job on the bucket.
The biggest problem with using hole saws in steel is the speed of the drill or drill press. Most are way too fast. Also you have to take time to clear chips as mentioned above and keep the the cut well oiled while cutting.
1 3/4 ≈ 2” hole
c = π d
3.14 x 2 = 6.28 inch ≈ .5 foot
From my chart for Plain Carbon Steels, AISI–1019, 1020, 1030, 1040, 1050, 1060, 1070, 1080, 1090
Using a high speed steel cutter, on plain carbon steel the cutting rate varies from 15 to 120 feet per minute, depending on the hardness. For the softest type, desired speed is between 80-120 FPM
If you pick 100 fpm as a starting point, 100fpm ÷ .5ft = 200 RPM for your 1 3/4” hole saw. This is the MAXIMUM speed it should run. For best results and deviation from this should be lower rather then faster.
Since it is difficult to know for sure what type of steel you have, the maximum speed may very well be lower than this, perhaps down to 30 rpm for the hardest type I see on my chart.
How do you get your bucket to empty out? I have a very similar trenching bucket but it always packs.up with my clay soils and I can hand dig a trench just about faster than I can using the old hoe. Spend more energy and time digging packed dirt out of the bucket than I do running the machine. Usually default to the wider digging bucket and ensuing mess
This is how I clear sticky material from a hoe bucket. Attach a chain to the arm. Run that down to the bucket. Add a second chain to make a "V". Attach the 2 ends of the V to the bucket. Adjust the length so the chain is almost straight but not tight with the bucket fully uncurled. When digging the mud will push the chain deep into the bucket, When you uncurl the bucket, the chain pulls the mud out.
elk-a-holic (Aug 26, 2024), Jon (Aug 26, 2024), mtsmith14 (Aug 28, 2024), Ralphxyz (Sep 2, 2024)
Thanks hemmjo! We've added your Hoe Bucket Cleaning Method to our Farm and Garden category,
as well as to your builder page: hemmjo's Homemade Tools. Your receipt:
New plans added on 09/11: Click here for 2,453 plans for homemade tools.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks