Mark,
Worthy winner.
I copied it and have now retired my transformer based device. Actually I want the transformer for another tool.
Beserkleyboy (May 18, 2019), freddo4 (May 17, 2022), kbars121321 (May 7, 2022)
Tony,
I am glad it worked for you. Mine gets a regular workout. For some reason my shed seems to have a magnetic charge. I have heard that a nearby lightning strike can magnetise large structures. We get lots of thunderstorms where we live and we had a very close strike a few years ago that killed the quartz clock mechanism in our kitchen!
Regards,
Mark Presling
freddo4 (May 17, 2022)
Lightening can be destructive. A couple of years ago it destroyed the controller in a pellet fire heater as well as some UPS and other things. I made a new controller for the fire from an Arduino which works better than the original.
I use a some magnetic bars as tool holders and that is one reason that I sometimes need to demagnetise. When I saw your idea I knew that it would work but I was uncertain as to whether it would work well enough. It has proven itself on calipers, drill bits (I don't know how or why they get magnetised) and most screw drivers but I have one screw driver that refuses to be demagnetised. I wonder whether it is intended to be magnetised and perhaps has a magnet hidden in the handle. It is not strongly magnetised but it just will not give up what it has.
For bigger tools, I demagnetize with a bulk tape eraser (remember those?). For smaller tools I use my old Weller soldering gun.
However, when I saw Mark Presling's ingenious mechanical demagnetizer...
DIY Demagnetising tool that works
I had to have a miniature version for my in-house small job bench. Beyond its undeniable coolness, it would save me the trip to the garage to retrIeve the soldering gun and could be spun with any of the Dremel/Foredom-like tools lying on the bench.
I was fortunate to have some 1" fender washers with a 1/8" hole that just fits a 5-40 screw to provide a shaft to grasp in the Dremel. Six Harbor Freight 5/16" diameter super magnets were epoxied to the washer in an alternating polarity configuration.
Spun at even a low speed, it does a fine job of demagnetizing small tools.
![]()
---
Regards, Marv
Experience is always far worse than pessimism
albertq (Nov 26, 2023), DIYer (May 19, 2022), freddo4 (May 17, 2022), Jon (May 19, 2022), mwmkravchenko (May 16, 2022), rebuilder1954 (May 21, 2022), rlm98253 (May 16, 2022), techcollect (May 17, 2022)
It is now 3 years since I made my version inspired by Mark's. I made a stand alone version with the rotor driven by an old washing machine pump motor. The motor and switch are encased in a plastic junction box and sit on a bench permanently. It gets used regularly. I am still at a loss to understand how calipers get magnetised but they do, although not often.
DIYer (May 19, 2022), mwmkravchenko (May 16, 2022), rlm98253 (May 16, 2022), uv8452 (May 22, 2022)
Thanks mklotz! We've added your Mechanical Demagnetizer to our Miscellaneous category,
as well as to your builder page: mklotz's Homemade Tools. Your receipt:
New plans added on 08/30: Click here for 2,430 plans for homemade tools.
Only after posting my thread did I notice that there was another one, containing a 3D file of this tool. Great minds think alike...Magnetising and demagnetising tools.
I happily adopted his concept.![]()
Last edited by yair feldmann; Jun 4, 2024 at 02:56 PM.
Thanks yair feldmann! We've added your Demagnetizing Tool to our Miscellaneous category,
as well as to your builder page: yair feldmann's Homemade Tools. Your receipt:
New plans added on 08/30: Click here for 2,430 plans for homemade tools.
There are currently 2 users browsing this thread. (0 members and 2 guests)
Bookmarks