Free 186 More Best Homemade Tools eBook:  
Get tool plans

User Tag List

Page 2 of 3 FirstFirst 1 2 3 LastLast
Results 11 to 20 of 26

Thread: Quick Change Lathe Turret

  1. #11
    PJs
    PJs is offline
    Supporting Member PJs's Avatar
    Join Date
    Sep 2014
    Location
    Northern CA
    Posts
    1,844
    Thanks
    8,431
    Thanked 1,129 Times in 725 Posts

    PJs's Tools
    Old_Toolmaker, not only are these Eye Candy but the design is quite brilliant, imho. I look forward to Jon posting your plans!

    I noticed in pic 3 there is a dowel or gauge pin being used as a stop...is that for using smaller tool bits with out changing the holder setting? Nice idea also if it is.

    Sorry on the late show here but so glad I save that email for this!

    Thanks Much!

    PJ

    186 More Best Homemade Tools eBook
    ‘‘Always do right. This will gratify some people and astonish the rest.’’
    Mark Twain

  2. #12
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 457 Times in 184 Posts

    old_toolmaker's Tools
    PJs,
    Thank you for the nice complement!
    You are correct, the dowel pin is being used as spacer because the tool bit I chose to use is smaller than what the QC Turret was designed for.

    2,000+ Tool Plans
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

  3. The Following User Says Thank You to old_toolmaker For This Useful Post:

    PJs (Sep 12, 2018)

  4. #13
    Supporting Member Ralphxyz's Avatar
    Join Date
    Dec 2016
    Posts
    1,733
    Thanks
    3,229
    Thanked 295 Times in 241 Posts

    Ralphxyz's Tools
    No Dick, I have no shop time, I am fighting termite damage this summer.

    Possible this winter.

    I have a 7x12 mini lathe which I thought the small QCTP would work on.
    I also have a 12x36 lathe which I figure your larger QCTP would work on.

    Ralph

  5. #14
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 457 Times in 184 Posts

    old_toolmaker's Tools
    Those tool posts should work out fine. I have had the small QC tool post on my mini lathe and it works out well. What part of the country do you live? I am assuming you are somewhere in the south with the termite issues. I hope you are able to get them under control.
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

  6. #15
    Supporting Member Ralphxyz's Avatar
    Join Date
    Dec 2016
    Posts
    1,733
    Thanks
    3,229
    Thanked 295 Times in 241 Posts

    Ralphxyz's Tools
    I am on the eastern end of Long Island NY.

    Close to actually putting siding back on the sill has been replaced and framing up 2 feet.
    I started by myself Memorial Day this spring.

    Ralph

  7. #16
    Supporting Member Toolmaker51's Avatar
    Join Date
    Feb 2016
    Location
    Midwest USA
    Posts
    5,334
    Thanks
    7,044
    Thanked 3,012 Times in 1,901 Posts

    Toolmaker51's Tools
    I wondered too, how/ what four-sided cam could be actuated and deliver equal and sufficient clamping at each side; tough! Then, a single cam is less desirable for changes by disturbing unintended holders. Your solution is far more effective and sensible. The turret feature makes this stellar! This can really generate parts, do you use a DRO? Had you ever tested the repeatability? About the Vee'd holder; the horizontal aspect is obvious, what did you expect from the vertical? That might be a holder missing from all the commercial QC sets...and an opportunity...

    And the dowel. Beside solving height of a small bit, it cures my issue about QCTPs. It can shed chips collecting on the post and disturbing intended centerline adjustments.
    Last edited by Toolmaker51; Sep 12, 2018 at 07:57 PM. Reason: Coupled to PJs observation of dowel
    Sincerely,
    Toolmaker51
    ...we'll learn more by wandering than searching...

  8. The Following User Says Thank You to Toolmaker51 For This Useful Post:

    PJs (Sep 13, 2018)

  9. #17
    Jon
    Jon is offline Jon has agreed the Seller's Terms of Service
    Administrator
    Supporting Member
    Jon's Avatar
    Join Date
    Jan 2012
    Location
    Colorado, USA
    Posts
    26,445
    Thanks
    8,100
    Thanked 40,270 Times in 11,779 Posts
    Congratulations old_toolmaker - your Quick Change Lathe Turret is the Homemade Tool of the Week!

    Big week around here! Lots of traffic (our 2nd biggest week ever), and an unusual amount of high quality homemade tools, many of which could've won on many other weeks.

    Some good picks from this week:

    Balanced Lathe Dog by natie123
    Drill Press Grinder Attachment by Tuomas
    Boilover Prevention Tool by Christophe Mineau
    Angle Plates by rossbotics
    Edge Finder by threesixesinarow
    Stitching Clamp by Christophe Mineau
    Counterbore Cutters by olderdan
    Stitching Awls by Christophe Mineau
    Countersink Stand by Shelly142
    Stitching Extension Clamp by Christophe Mineau
    Forge by celsoari


    old_toolmaker - we've added your tool entry to our All Homemade Tool of the Week winners post.

    You'll be receiving a $25 online gift card, in your choice of Amazon, PayPal, or bitcoin. Please PM me your current email address and gift card choice and I'll get it sent over right away.

    Most importantly - this is your 3rd Homemade Tool of the Week win! You join these other 3-Time Homemade Tool of the Week winners: rgsparber, rossbotics, mr95gst, Paul Jones, Christophe Mineau, Captainleeward, immortalx, scorch, Brendon, Frank S, mklotz, Vyacheslav.Nevolya, brianhw, LMMasterMariner, jjr2001, Tuomas, olderdan, tonyfoale, Mikhandmaker, thehomeengineer.

    You'll notice the 3-Time Homemade Tool of the Week award trophy graphic in your postbit beneath your avatar.




    Here are all of your winning tools:



  10. The Following User Says Thank You to Jon For This Useful Post:

    PJs (Sep 15, 2018)

  11. #18
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 457 Times in 184 Posts

    old_toolmaker's Tools
    Ralphxyz,

    Just an FYI.
    I sent the plans to Jon. After he gets them refined they will be posted for sale.
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

  12. The Following User Says Thank You to old_toolmaker For This Useful Post:

    PJs (Sep 15, 2018)

  13. #19
    PJs
    PJs is offline
    Supporting Member PJs's Avatar
    Join Date
    Sep 2014
    Location
    Northern CA
    Posts
    1,844
    Thanks
    8,431
    Thanked 1,129 Times in 725 Posts

    PJs's Tools
    Congratulations Dick on your third, stunning tool of the week award. Thank you also for creating the plans for these. Mighty fine work!

    PJ
    ‘‘Always do right. This will gratify some people and astonish the rest.’’
    Mark Twain

  14. #20
    Supporting Member old_toolmaker's Avatar
    Join Date
    Dec 2017
    Location
    Cape Coral, FL
    Posts
    579
    Thanks
    647
    Thanked 457 Times in 184 Posts

    old_toolmaker's Tools
    Toolmaker51,

    Those are all good questions!
    Yes, I do use a DRO. Repeat-ability is within a few tenths on each tool. About the vertical Vee:I just put that in there on the off chance it might be useful. I use a vertical milling head on my lathe so sometimes it is handy to have it there when I need to drill a vertical hole through a shaft and I need the additional clearance. Although I have not used it much.
    Dick


    Links to some of my plans:

    https://www.homemadetools.net/forum/...965#post105972 OFF-SET TAILSTOCK CENTER PLANS
    http://www.homemadetools.net/forum/s...995#post112113 SMALL TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/l...994#post112111 LARGE TURRET TOOL POST PLANS
    http://www.homemadetools.net/forum/m...383#post110340 MINI-LATHE CARRIAGE LOCK PLANS
    http://www.homemadetools.net/forum/s...191#post106483 SMALL QC TOOL POST PLANS
    http://www.homemadetools.net/forum/q...849#post119345 QUICK CHANGE LATHE TURRET
    http://www.homemadetools.net/forum/m...949#post119893 MINI LATHE COMPOUND PIVOT MODIFICATION

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •