LinkBack URL
About LinkBacksHello Toolmaker51, Thelt, Happy holidays and thanks for being part of the Home made tool community.
Hello Toolmaker51, Thelt, Happy holidays and thanks for being part of the Home made tool community.
Last edited by Captainleeward; Dec 19, 2017 at 10:31 AM.
Toolmaker51 (Dec 23, 2017)
Hello Captainleeward, I really like your solution,I have one of those drill presses with the open slot round tables as well, additionally I have one with a larger square table with the T slots milled in, both are floor models. The round one just like yours is a royal pain to try and clamp anything down on. the table in my opinion is too thin to actually use the slotted holes for much. So after I found a vice with built in X & Y movement I mounted it to that table to take care not to potentially break out the slots I used strips of 1/4 by 1 1/2 Flat bar as washers underneath. I use my other drill press for any thing that does not require a vice.
Never try to tell me it can't be done
When I have to paint I use KBS products
Captainleeward (Dec 22, 2017), Paul Jones (Dec 20, 2017)
Hi Frank, Thanks for your input I liked it Happy holidays to you too...:O)
Thanks Captainleeward! We've added your Drill Press Table Modification to our Drilling and Drill Presses category,
as well as to your builder page: Captainleeward's Homemade Tools. Your receipt:
New plans added on 11/20: Click here for 2,589 plans for homemade tools.
Captainleeward (Dec 22, 2017), rlm98253 (Dec 22, 2017)
Congratulations Captainleeward - your Drill Press Table Modification is the Homemade Tool of the Week!
We've seen many drill press mods, but this is a rare one, and certainly also qualifies for a "Why Didn't I Think of That" award.
Some good picks from this week:
Lathe by rep
Mill DRO by ruxu
Corner Clamps by Tuomas
Pearl Tweezers by mklotz
Pneumatic Drawbar by thehomeengineer
Tractor Pusher Blade by Viny
Wood Stove Ashes Fork by Frank S
Dial Indicator Holder by Captainleeward
Circle Center Finder by Downeast Thunder
Laser Position Indicator by scorch
Tractor Rear Brush Guard by Frank S
ER25 Collet Chuck by thehomeengineer
Arduino Debugging Tool by rgsparber
Tractor Front Brush Guard by Frank S
Captainleeward - we've added your tool entry to our All Homemade Tool of the Week winners post. And, you'll be receiving a $25 online gift card, in your choice of Amazon, PayPal, or bitcoin. Please PM me your current email address and gift card choice and I'll get it sent over right away.
Most importantly - this is your 3rd Homemade Tool of the Week win! You join these other 3-Time Homemade Tool of the Week winners: rossbotics, mr95gst, Paul Jones, Christophe Mineau, immortalx, scorch, Brendon, Frank S, mklotz, Vyacheslav.Nevolya, brianhw, LMMasterMariner, jjr2001, Tuomas, olderdan, tonyfoale.
You'll notice the 3-Time Homemade Tool of the Week award trophy graphic in your postbit beneath your avatar.
Here are all of your winning homemade tools:
New plans added on 11/20: Click here for 2,589 plans for homemade tools.
Captainleeward (Dec 22, 2017)
Great idea Captain Lee Ward. My drill press table needs the same mod.
Out to the boat store for some 5200 Calk..
Thanks again for the tip.
Now I have 2 Captain Lee projects to do.
The other one is the Kant Twist Clamps.
http://www.homemadetools.net/forum/k...873#post102722
Cheers JR
Captainleeward (Dec 22, 2017)
JJR2001 Hello and thanks for your kudos by the way my handle is captainleeward as in the leeward side of the island safe harbors ect. my first name is Ward and middle is Lee. You would be surprised how many people are named Ward. just some trivia. Ha ha. Cap.
jjr2001 (Dec 23, 2017)
Very good Captainleeward...Safe side of the island...Great place to anchor down.
Cheers, JR
Captainleeward (Dec 24, 2017)
Great idea! Thanks,
Dave
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
Bookmarks