Diy 20 ton hydraulic bench top press

**Tuomas** · May 14, 2021, 08:30 AM

My new video is about making 20 ton hydraulic bench top press.

Top is connected to the frame with 20mm ldx pins and four M8 bolts. ( bolts just spline axles against frame, and remove clamp )

Diy 20 ton hydraulic bench top press-1.jpg

Press can be disassembled easily, this helps if i need to carry it out from our basement.
Also, frame is designed to be used with 30 ton jack. Now i have room to upgrade it.
( only bed needs to be replaced with stronger one ) Making upgrade is easy, when i can remove top from the frame.

Diy 20 ton hydraulic bench top press-3.jpg

Jack after modification.
Weld inlet is for filling the jack. That can be leave out, and use " breathing valve " for filling instead.
I just liked to have easy access to fillport.

Diy 20 ton hydraulic bench top press-2.jpg

**hemmjo** · May 15, 2021, 05:54 AM

I wish I could keep my shop that clean!! nice press.

**DIYer** · May 15, 2021, 06:57 AM

Thanks Tuomas! We've added your Hydraulic Benchtop Press to our Brakes and Presses category,
as well as to your builder page: Tuomas's Homemade Tools. Your receipt:

Hydraulic Benchtop Press by Tuomas

tags: press, hydraulic, bottle jack

**Tuomas** · May 15, 2021, 04:37 PM

Originally Posted by hemmjo

I wish I could keep my shop that clean!! nice press.

Thanks. I like to keep things so that i found them.

**Tuomas** · May 20, 2021, 01:40 AM

Here's a size comparison with my first press.

Diy 20 ton hydraulic bench top press-fb_img_1621492552647.jpg

Old one is still useful when bending thinner / really small materials. Also i had made a set of bending dies to it, so i decided to keep it in use too.

**Tuomas** · May 29, 2021, 07:35 AM

Made a table / stand for the press.
Table has two other uses too, those can be seen later.

Diy 20 ton hydraulic bench top press-img_20210529_134836_006.jpg

Diy 20 ton hydraulic bench top press-img_20210529_134836_045.jpg

Diy 20 ton hydraulic bench top press-img_20210529_134836_049.jpg

**Claudio HG** · May 29, 2021, 11:38 AM

Wow that's badass press. Impressive.

**Tuomas** · May 30, 2021, 04:42 AM

Originally Posted by Claudio HG

Wow that's badass press. Impressive.

Thank you.

**Tuomas** · May 31, 2021, 01:21 PM

Because there was empty space on this side of the table.
I made a simple clamp rack to get that space to use.

Diy 20 ton hydraulic bench top press-img_20210531_211644_559.jpg

Material is stainless steel. Leftover pieces, so i just brushed it, instead of proper polishing.

Diy 20 ton hydraulic bench top press-img_20210531_211644_577.jpg

Diy 20 ton hydraulic bench top press-img_20210531_211644_588.jpg

**Tuomas** · Jun 1, 2021, 02:04 AM

I had some problems with my camera, couldn't restore all pictures earlier. ( and lost some of them totally, i supposed to add more pictures about the structure )

Top frame of the table is made from split 40mm x 40mm x 4mm square tubing. Rest of the frame is made from 40 x 40 x 4 square tubing. Shelves are made from 2mm stainless 316 sheet. Edges are bend down to increase strength of the shelf.

I marked the cutting line 6mm from the outer edge, and made cut with an angle grinder using 1mm thick wheel.

This way i got angle irons with a rounded edge, also i got the height suitable for the grill that's weld to the top.
But still having bottom side of the fabricated angle iron in same width with the actual frame of the table. ( size of the made angle iron 40mm x 33mm x 4mm )

Using square tubing didn't cost more.
I got enough angle iron from a 1300mm long piece of square tubing. ( 13€ )
When i would have need to buy 2600mm of 40mm x 40mm angle iron ( 12€ ), and still need to cut 6mm out from the one edge, to get it same height with the top grill. ( and wouldn't got nice round edge to it )