Free 186 More Best Homemade Tools eBook:  
Get tool plans

User Tag List

Results 1 to 8 of 8

Thread: Demagnetizer

  1. #1
    Supporting Member
    Join Date
    May 2016
    Posts
    79
    Thanks
    4
    Thanked 214 Times in 44 Posts

    Don42's Tools

    Demagnetizer

    Small hand tools like screwdrives and tweezers sometimes get magnetized. That can sometimes be useful, but other times a nuisance. I made a demagnetizer out of a soldering gun -- and the soldering gun can also be quickly restored to its original purpose.

    I made a three-turn coil out of 6 gage solid copper ground wire, which is sold by the foot at Home Depot. I wound the wire around a 3/4" dia piece of cold roll to use as a mandrel. I made two nuts (7/16 x 14tpi) out of brass, with holes thru them. The holes are bigger than the original nuts; I made them 0.228" (#1 drill) to comfortably clear the .204" dia copper wire. I also made little washers to silver-braze on the ends of the coil so the nuts could hold the coil in the soldering gun.

    Demagnetizer-coil_with_nuts_and_stops.jpg

    Demagnetizer-demagnetizer.jpg

    That's all there is to it! Insert the tool (screwdriver, whatever) into the coil, pull the trigger on the soldering gun and slowly withdraw the tool. You'll notice that the coil's magnetic field exerts a fairly strong attraction to a ferromagnetic object within it. When the tool is well clear of the coil, release the trigger. Best not to hold it down too long because the coil will get quite hot fairly quickly. It can also re-magnitize tools. Insert tool into coil, pull trigger and release. Test for magnetism. The trigger must be released when the 60 Hz line voltage is near its peak. That's trial and error but it never takes more than a few tries.

    I did some measurements. The current flowing thru that coil is 990 amps!

    186 More Best Homemade Tools eBook
    Last edited by Don42; Aug 26, 2018 at 03:43 PM. Reason: new info

  2. The Following 20 Users Say Thank You to Don42 For This Useful Post:

    12L14 (Jul 31, 2019), 4evrdrmn (Aug 27, 2018), almarghi (Aug 27, 2018), jimfols (Jan 1, 2019), J_P (Aug 31, 2018), katy (Aug 12, 2021), KickStart (Jan 2, 2019), KustomsbyKent (May 9, 2019), Manitoba Man (Aug 13, 2021), mklotz (Aug 26, 2018), mr_modify1 (Jun 17, 2022), mwmkravchenko (Aug 11, 2021), Paul Jones (Aug 15, 2021), PJs (Aug 28, 2018), rlm98253 (Jan 1, 2019), rossbotics (Aug 26, 2018), Scotsman Hosie (May 3, 2019), Seedtick (Aug 27, 2018), suther51 (Aug 27, 2018), that_other_guy (Aug 27, 2018)

  3. #2
    Content Editor
    Supporting Member
    DIYer's Avatar
    Join Date
    Aug 2013
    Posts
    3,055
    Thanks
    793
    Thanked 1,888 Times in 1,683 Posts


    Thanks Don42! We've added your Demagnetizer to our Electrical category,
    as well as to your builder page: Don42's Homemade Tools. Your receipt:




    2,000+ Tool Plans

  4. #3
    Supporting Member
    Join Date
    Apr 2018
    Location
    southern Calif.
    Posts
    15
    Thanks
    0
    Thanked 52 Times in 4 Posts

    paulk's Tools
    Slick!! I need to magnetize a dipstick. This should work great. Paulk

  5. #4
    Supporting Member ranald's Avatar
    Join Date
    Jan 2018
    Location
    Black Mountain Queensland
    Posts
    1,326
    Thanks
    992
    Thanked 367 Times in 256 Posts

    ranald's Tools
    Quote Originally Posted by Don42 View Post
    Small hand tools like screwdrives and tweezers sometimes get magnetized. That can sometimes be useful, but other times a nuisance. I made a demagnetizer out of a soldering gun -- and the soldering gun can also be quickly restored to its original purpose.

    I made a three-turn coil out of 6 gage solid copper ground wire, which is sold by the foot at Home Depot. I wound the wire around a 3/4" dia piece of cold roll to use as a mandrel. I made two nuts (7/16 x 14tpi) out of brass, with holes thru them. The holes are bigger than the original nuts; I made them 0.228" (#1 drill) to comfortably clear the .204" dia copper wire. I also made little washers to silver-braze on the ends of the coil so the nuts could hold the coil in the soldering gun.

    Click image for larger version. 

Name:	coil_with_nuts_and_stops.jpg 
Views:	575 
Size:	59.4 KB 
ID:	25268

    Click image for larger version. 

Name:	demagnetizer.jpg 
Views:	676 
Size:	55.1 KB 
ID:	25269

    That's all there is to it! Insert the tool (screwdriver, whatever) into the coil, pull the trigger on the soldering gun and slowly withdraw the tool. You'll notice that the coil's magnetic field exerts a fairly strong attraction to a ferromagnetic object within it. When the tool is well clear of the coil, release the trigger. Best not to hold it down too long because the coil will get quite hot fairly quickly. It can also re-magnitize tools. Insert tool into coil, pull trigger and release. Test for magnetism. The trigger must be released when the 60 Hz line voltage is near its peak. That's trial and error but it never takes more than a few tries.

    I did some measurements. The current flowing thru that coil is 990 amps!
    Very Interesting!

  6. #5

    Join Date
    Apr 2018
    Posts
    20
    Thanks
    0
    Thanked 7 Times in 6 Posts
    Quote Originally Posted by Don42 View Post
    Small hand tools like screwdrives and tweezers sometimes get magnetized. That can sometimes be useful, but other times a nuisance. I made a demagnetizer out of a soldering gun -- and the soldering gun can also be quickly restored to its original purpose.

    I made a three-turn coil out of 6 gage solid copper ground wire, which is sold by the foot at Home Depot. I wound the wire around a 3/4" dia piece of cold roll to use as a mandrel. I made two nuts (7/16 x 14tpi) out of brass, with holes thru them. The holes are bigger than the original nuts; I made them 0.228" (#1 drill) to comfortably clear the .204" dia copper wire. I also made little washers to silver-braze on the ends of the coil so the nuts could hold the coil in the soldering gun.

    Click image for larger version. 

Name:	coil_with_nuts_and_stops.jpg 
Views:	575 
Size:	59.4 KB 
ID:	25268

    Click image for larger version. 

Name:	demagnetizer.jpg 
Views:	676 
Size:	55.1 KB 
ID:	25269

    That's all there is to it! Insert the tool (screwdriver, whatever) into the coil, pull the trigger on the soldering gun and slowly withdraw the tool. You'll notice that the coil's magnetic field exerts a fairly strong attraction to a ferromagnetic object within it. When the tool is well clear of the coil, release the trigger. Best not to hold it down too long because the coil will get quite hot fairly quickly. It can also re-magnitize tools. Insert tool into coil, pull trigger and release. Test for magnetism. The trigger must be released when the 60 Hz line voltage is near its peak. That's trial and error but it never takes more than a few tries.

    I did some measurements. The current flowing thru that coil is 990 amps!


    just for your information. You can get brake line tubing nuts that have a 7/16-14 thread.

  7. The Following User Says Thank You to 11thhourfabrication For This Useful Post:

    Tooler2 (May 4, 2019)

  8. #6
    Supporting Member thevillageinn's Avatar
    Join Date
    Jul 2017
    Posts
    229
    Thanks
    387
    Thanked 66 Times in 40 Posts

    thevillageinn's Tools
    Thanks for the inspiration! I made a similar coil for my soldering gun which has taken care of the fine steel swarf from filing and grinding from hanging on my screwdrivers. I didn't have any copper as heavy as yours but I had some 12ga which I twisted together and bent to fit.

  9. #7
    Supporting Member
    Join Date
    May 2016
    Posts
    79
    Thanks
    4
    Thanked 214 Times in 44 Posts

    Don42's Tools
    Quote Originally Posted by thevillageinn View Post
    Thanks for the inspiration! I made a similar coil for my soldering gun which has taken care of the fine steel swarf from filing and grinding from hanging on my screwdrivers. I didn't have any copper as heavy as yours but I had some 12ga which I twisted together and bent to fit.
    Glad it's working for you. Swarf on tools can be a real nuisance!

  10. #8
    mr_modify1's Avatar
    Join Date
    Nov 2021
    Posts
    103
    Thanks
    17
    Thanked 251 Times in 64 Posts

    mr_modify1's Tools
    Nice job great idea.



    2,000+ Tool Plans

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •